Air Mag C11 Spare Clip $7.47

Add Comment | Related Links | TrackBack
Related Content

Air Mag C11 Spare Clip $7.47

Found the Crosman Air Mag C11 Spare Clip at Wal-mart for $7.47. This airsoft pistol magazine costs about $15 at online airsoft retailers.

It is the same magazine as the one Umarex Combat Zone Enforcer uses, even though it not shown as compatible on the packaging. On the packaging, it shows this magazine is compatible with "Compatible AVEC", Air Mag C11 (SAMC11, AMC11P, SAMC11CB), Air Mag 1911 (60001, 60002), Marines CP01 (MCCP01), Z11 & TACZ11 Zombie Eliminator (AMZ11).

Attached Image:

Air Mag C11 Spare Clip Package Front.jpg

Jake
Mon, 15 Sep 2014 20:12:01 +0400

You can order it online from Walmart.com!. In fact, you can get two of them for $9.66 online. Free shipping available on order over $50. Or you can ship to Walmart store for free store pickup.

Jake
Mon, 15 Sep 2014 22:38:03 +0400

Well, it seems that these magazines are not quite compatible with the Umarex Combat Zone Enforcer. They are exactly the same size and have the same mechanism. The only difference is the magazine latching notch (see photo below). The magazine on the top is from the Umarex Combat Zone Enforcer. The magazine below is the Air Mag C11 Spare Clip. They don't line up quite right. It would require some cutting to get these new mags to work with the Umarex Combat Zone Enforcer.

Attached Image:

Mag Comparison (Small).jpg

Jake
Wed, 24 Sep 2014 11:56:25 +0400

The following photo shows the same mags above, but provides a close-up view of the notches placement. Magazine on top is for Umarex Combat Zone Enforcer. The magazine below is the Air Mag C11.

Attached Image:

Notches Close Up.jpg

Jake
Fri, 20 Mar 2015 06:24:52 +0300

My friend has the Crosman Undead Apocalypse Z11 Zombie Eliminator. The magazine that comes with the Z11 is the exact same magazine as the one that comes with my Umarex Combat Zone Enforcer. Photo below shows both magazines have the magazine retention notches in the same places; Umarex Combat Zone Enforcer magazine on top and Crosman Undead Apocalypse Z11 Zombie Eliminator on bottom.

However, the Crosman Undead Apocalypse Z11 Zombie Eliminator actually works with the Air Mag C11 Spare Clip. The Z11 is basically the Crosman C11 airsoft pistol painted zombie green. The Black Ops BOA airsoft pistol also looks just like the C11.

Note that I also have the WinGun M87 CO2 airsoft pistol. It also comes with the same magazine as the Umarex Combat Zone Enforcer (CZE) and the Crosman Undead Apocalypse Z11 Zombie Eliminator. The WinGun M87 uses the same notch as the Umarex CZE. Therefore, the Air Mag C11 Spare Clip does not work in the WinGun M87.

Attached Image:

CZE and Z11 come with same mags.jpg

Jake
Fri, 20 Mar 2015 06:31:12 +0300

My friend has shown me a third type of similar magazine. Photo below shows the Umarex Combat Zone Enforcer magazine (top) compared to this third type of magazine (bottom). The third magazine is made out of plastic with metal backing. It's not made as robust as the full metal magazines. And it's notched the same way as the Air Mag C11 Spare Clip on the side. However, note that there isn't a notch on top along the BB track. Not sure if this top notch is used by any airsoft guns.

This third type of magazine works with the Z11, but will not work with the CZE. By deduction, the Z11 uses the bottom notch, whereas the CZE uses the top notch.

However, this third type of magazine is made out of hard plastic. That means it's much easier to cut a side notch into this mag than the metal mags. With a hot knife, you can easily slide off some plastic and make it work with the Umarex CZE and the WinGun M87.

Attached Image:

Third Type Plastic Mag.jpg

Jake
Fri, 20 Mar 2015 06:33:15 +0300

Reading online reviews, it seems that these types of mags are also used in Beretta Elite II, Phoenix Compact M84, Ruger P345PR Pistol, TSD Sports SD1911 SDGP304, TSD Sports M9 SDGP302, and TSD Tactical M92. Though it is not clear with pistol uses which notch.

Jake
Fri, 20 Mar 2015 06:34:05 +0300

My friend asked me to cut a slot into the plastic mag to see if it would work with the Combat Zone Enforcer... He wanted to get CZE, too. I used a hot knife and in less than the time to warm up the knife, it was done. Photo below shows the newly cut slot. This mag works in the CZE.

Attached Image:

IMG_20150319_223803.jpg

Jake
Fri, 20 Mar 2015 10:18:18 +0300

Add Comment | Related Links | TrackBack
Related Content

Did your message disappear? Read the Forums FAQ.

Add Comment

Spam Control | * indicates required field

TrackBack

TrackBack only accepted from WebSite-X Suite web sites. Do not submit TrackBacks from other sites.

Send Ping | TrackBack URL | Spam Control

No TrackBacks yet. TrackBack can be used to link this thread to your weblog, or link your weblog to this thread. In addition, TrackBack can be used as a form of remote commenting. Rather than posting the comment directly on this thread, you can posts it on your own weblog. Then have your weblog sends a TrackBack ping to the TrackBack URL, so that your post would show up here.

Your Name: *
E-mail:
	Remember Me!
Comment: *
	File attachment is optional. Please do not attach a file to your submission unless it is relevent.
Attach File: (20 MB Max)
Spam Protection: *	Answer of 3 + 3?
	Click button only once, please!