64 Users Online
Add Comment
|
Related Links
|
TrackBack
Related Content
The airsoft electronic gun (AEG) is really not a very complicated device. It basically pushes the BB out of the muzzle with a puff of air. How fast the AEG shoots depends on the strength of the air puff. The biggest culprit of FPS loss on an AEG is air leak, which weakens the puff of air. Here are some potential areas for air leaks and how to test for leak.
- Hop-Up Bucking and Gearbox Nozzle: During the firing of the AEG, the BB feeder hole is sealed by the gearbox nozzle. Test for air leak here with an assembled gun. Place a piece of paper over the BB feeding tube. Dry fire the gun. The paper should not move. If it moves, then you have an air leak between the gearbox nozzle and the hop-up bucking.
- Inner Barrel and Hop-Up Unit: The inner barrel and the hop-up unit is considered as one unit once it is assembled. There are three holes in this system: 1) The end of the inner barrel; 2) The BB feeding tube; and 3) The end of the hop-up unit. With two of these three hole sealed with your finger, try blowing through the remaining hole. You should feel a lot of resistance. If you don't, there is an air leak somewhere.
- Inside the Gearbox: The biggest culprit is generally piston o-ring. That o-ring wears with every round fired. It needs to be replace more often than not. But before doing so, determine the location of the leak. Be sure the cylinder head is snug in the cylinder. Seal the cylinder head nozzle with your finger. Push the piston with the o-ring into the cylinder. You should not be able to push the piston into the cylinder pass the open port. If you do, you have a leak.
That's pretty much it. Only three major areas of air leaks in an AEG. If you can think of another, post it below.
Jake
Wed, 13 Nov 2013 03:09:54 +0300
Add Comment
|
Related Links
|
TrackBack
Related Content
Did your message disappear? Read the Forums FAQ.
TrackBack only accepted from WebSite-X Suite web sites. Do not submit TrackBacks from other sites.
Send Ping |
Spam Control
Title: Three Ways to Increase Your AEG Velocity
Weblog: GearHack
Excerpt: In the airsoft sport, it's in your best interest to bring your airsoft electronic gun (AEG) to the velocity limit of your local airsoft field. A faster gun shoots further than a slow one. In this article, we will present concrete method to increase the velocity, which is in feet-per-second (FPS), of . . .
Tracked: Wed, 14 May 2014 03:45:08 +0400
Title: O-Ring for AEG Piston Head
Weblog: Airsoft SpecOps
Excerpt: Everyone claims the o-ring for airsoft gearbox piston head is #14. But it's really hard to find o-rings based on that identification. Lowes doesn't carry o-rings based on that designation. Home Depot's web site shows that it carry #14 o-rings. But when I get there, I didn't see any o-rings with the . . .
Tracked: Thu, 07 Aug 2014 00:21:17 +0400
Title: O-Ring for AEG Cylinder Head
Weblog: Airsoft SpecOps
Excerpt: The o-ring for an airsoft electronic gun (AEG) cylinder head is the same as the AEG piston head. It is #14, which is 15/16 In. OD x 3/4 In. ID x 3/32 In. Wall. It is the same dimensions a s the #214 o-rings being sold at Home Depot. Be sure you match all three dimensions listed above.
Tracked: Thu, 07 Aug 2014 00:45:05 +0400
Title: Maximizing Compression in AEG Cylinder
Weblog: Airsoft SpecOps
Excerpt: The spring, gears, and trigger in an airsoft electronic gun (AEG) are all mechanical parts. They either work or don't work. Very easy to tell. But the cylinder, piston, and nozzle are pneumatic parts, which is "technology that deals with the study and application of pressurized gas to produce mechan . . .
Tracked: Thu, 07 Aug 2014 00:54:10 +0400
Messages, files, and images copyright by respective owners.
Fun for Photographers
Get Our
Memecoins!
